user_974580 (32)
Six electrical adapters.
The order below is the same order as the photographs.
20 amp male (dock) to 30 amp female (boat).
Marinco. Indicator ...
The spreader boots are made of soft white, synthetic rubber.
Designed to fit around the shroud and end of the spreader to protect the sails.
Moulde...
Blocks supplied with Furlex furling systems made by Selden.
Works with any system up to 8 mm head stay.
Block clamps on a 1” stanchion.
A univers...
Used on Espar, Webasto, Chinese forced air diesel heaters
Quality 60 mm diameter aluminum lined ducting.
For installations in boats, RV’s, Vans.
Va...
Open/Close Knob for Atkins and Hoyle Hatch
New, never installed.
These corrode and require replacement.
Found on many brands of boat, including C&C...
2 blade bronze sailboat propeller
17 inch diameter
13 inch pitch
Left hand rotation
1 inch bore
Very nice shape
No corrosion
Carry a spare if y...
18 ½ feet of 5/16 inch proof chain.
Good length and weight behind a boat anchor being handled without a winch.
Or useful as general purpose hauling,...
8’3” Dinghy
Built in Victoria by John Booth, who made hundreds of these.
Extremely well made.
Flotation tanks on both sides.
Soft plastic rub rail...
C.S. Johnson over center pelican hook
Easy to operate under load
Investment cast stainless steel
5/16” stud
Comes with coated stainless 3/16” wire...
Easy to open and close pelican hooks for lifeline gate
Takes 5/16” LH stud
Quality product made by Merriman
Compare with $75 new for one
All 4 for...
Clever device for picking up a mooring
Works with a simple in and out motion
Works with any size mooring line and is suitable for boats up to 50'
W...
Reliance MDR-2 zinc
2-13/16"
Includes two halves for securing to rudder or trim tab, and hardware.
Zinc anode for use in salt water.
New
STA-LOK stud
Fits 9/32” or 7 mm 1 X 19 wire
Stud is ½ x 20 TPI.
Product #036-07
Comes with 2 new wedges, one for standard wire, one for Dyform wir...
Polyform PG-1 Corner Dock Bumper
Measures 10 x 10 inches.
Polyform PG-2 Straight Dock Bumper
Measures 18 inches.
Protect your boat gelcoat and...
Made by Nico Fico, now Ronstan, Model 6741
Snap shackle allows quick setup, block easily opens to install line, and closes securely.
Cushioned ...
One Forespar Marelon 3/4” flush head thru-hull, ball valve, and tailpiece.
One Forespar Marelon 3/4” flush head thru-hull, seacock valve, and tailp...
Moulded mooring snubber in EPDM Rubber with 6 rope holes.
Absorbs shock loads and relieve tension on lines and deck fittings.
Heavy duty: Up to ¾...
-8 circuits
-5/16” diameter solid copper bolts
-Solid copper bus bar 1/4" x 2" x 5 1/2"
-Mounted on bakelite plate: 4” x 6 ½” x 3/8”
-New conditi...
Heavy Duty spinnaker pole slider for 1 ¼” t-track
Made of investment cast stainless steel
Ring just under .500" in diameter.
Spring pin that locks ...
Two Backing Plates for Andersen 40 winches, self-tailing or non self tailing.
Custom made of marine grade aluminum, 3/16” thick.
100 mm bolt circle,...
Works with Standard Horizon GPS CP 155C, CP175C, and CP1000C. May work with other units.
This is the “smart antenna” where a portion of the GPS’s br...
Functional and looks good in the galley or head.
16 inches x 3 inches by 1 3/4 inches.
Nicely made by Seateak.
New, never used.
Compare with $70...
Dynaline Cable cutters.
Aluminum drop forged handles and heat treated blades.
Capacity: up to 5/8" diameter’
23" overall length’
Used for:
-gen...
Low drag folding prop
This shape has more blade area than the Martec elliptical style
Motors better and unfolds more reliably
1 inch bore
Right ha...
Two Barient 21 2 speed winches
Base: 5 ½ inches
Height: 5 ½ inches
Drum diameter: 2 ¾ inches
Drum material: Anodized Aluminum
Rope friction s...
user_974580
user_974580